TPU hot melt adhesive film has garnered more and more attention as the use of hot-melt adhesive film has become more widespread; however, there are still a lot of people who aren't familiar with it very well. Since there are many different kinds of materials that can be used to make hot-melt adhesive film, and since the price difference between two different kinds of hot-melt adhesive film can frequently be quite significant, the question arises as to what factors are responsible for determining the price of hot-melt adhesive film.1. Make use of primary materialsHot melt adhesive films can be made from a wide variety of raw materials, including EVA, TPU, PES, PA, and PO, amongst others. These are just some of the Chinese names for common chemicals: ethylene-vinyl acetate copolymer, thermoplastic polyurethane, polyester, polyamide, and polyolefin. There are also variations in the formulas and particle grades that are used, as well as other aspects, within each category. Due to these disparities, the prices of the raw materials used to produce hot melt adhesive films can vary, which in turn leads to price variations for the finished product.

In addition, the price difference is fairly significant regardless of whether the raw materials are imported or produced domestically. It is possible to use relatively high-end imported raw materials when developing certain types of hot melt adhesive films for special applications. The prices of these raw materials are typically relatively high, which contributes to the price of these specific types of hot melt adhesive films. Tpu hot melt adhesive film will be significantly more expensive compared to the price of regular hot melt adhesive film.

2. The production process The production process of the hot melt tpu hot melt adhesive film will also, to a certain extent, affect the price of the hot melt adhesive film. It is difficult to generalize about the processability of raw materials because of the variety of characteristics that they share, such as film-forming properties and initial viscosity. If the coating method is required for the production of some of the raw materials, then the substrate will be used to carry the film of hot melt adhesive, and the cost of the substrate that corresponds to the coating method will be calculated. Because of the significant amount of some raw materials that are wasted during production, the overall cost of the finished product will be adjusted to reflect this fact.

- What is the pricing for the hot melt adhesive film

- When quoting prices, those in the adhesive industry frequently use the how much per ton metric, whereas those in the hot melt adhesive film industry typically use the how much per square meter metric instead

- The quotation can now be done in this more practical and logical manner

- In most cases, the question of how much per meter is not asked

- Because there are problems with the width

- Hot melt adhesive films are typically offered for sale in rolls and can be procured in a variety of dimensions pertaining to their thickness, width, and length

- The conventional thickness of hot-melt adhesive film is typically between 1

- 5 silk and 20 silk, which translates to 0

- 015mm-0

- 2mm

- The thickness unit of the hot-melt adhesive film is typically the silk, with 1 silk equaling 0

- 01mm

- The hot-melt tpu hot melt adhesive film does not fall outside of this range of thickness

- Products are typically not manufactured very frequently at all

- It is generally difficult to control the thickness tolerance if it is too thin or too thick if they are to be made because of the limitations of the machines

- If they are to be made

In most cases, the length of the die head on the machine that is used to make tpu hot melt adhesive film is between 1 and 2 meters. When the width is less than one meter, the cutting machine is typically used to cut the material according to the specifications provided by the customer. Therefore, you are able to be cut so long as the required width is narrower than the length of the die head that you are using. It will be difficult to handle if the required width is greater than the width of the die head, and it will only be possible to connect it after it has been produced. In the event that it must be manufactured, the only option is to switch to a larger die head. The length of each roll of hot melt adhesive film ranges anywhere from 100 meters to two hundred meters, but it can also be tailored to the specifications required by individual customers. The product's thickness directly correlates to the number of meters that can be produced; conversely, the thinner the product, the more meters that can be produced. We will not be affected by the width when we are obtaining the quotation; however, we are frequently affected by the thickness and the material.

This is due to the fact that the unit price is calculated by the square. There is a natural disparity in the costs associated with the various types of materials. When a material is increased in thickness without a corresponding increase in the amount of material used, the price will increase proportionally.

4. What information can you provide me regarding hot melt adhesive film? Find a hot melt adhesive film and figure out how much it costs if you are a buyer. If you are a buyer, you need to do this. If this is the case, we recommend that you first identify one or more hot melt adhesive films that are capable of meeting the requirements, and then follow up with a specific inquiry. First and foremost, you need to know what material you need hot melt adhesive film to bond before you can choose the right type of hot melt adhesive film. This is because the material is connected to the determination of the type of hot melt adhesive film, and after that, you need to know what kind of bonding process you plan to use in order to decide whether there is a substrate or Hot melt  without a substrate. The manufacturer of hot melt adhesive film will not be able to provide you with recommendations for suitable hot melt  products or suitable product specifications until these two aspects have been clarified. The general manufacturer will then provide you with a step-by-step quotation according to your usage, and the quotation will be calculated based on the square price. After these have been determined, the quotation will be given to you.

The price is typically converted based on the price per square meter, though you can of course also consult the price calculated in units of meters, rolls, and tons.